Related changes
← Errors
Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.
List of abbreviations:
- N
- This edit created a new page (also see list of new pages)
- m
- This is a minor edit
- b
- This edit was performed by a bot
- (±123)
- The page size changed by this number of bytes
7 September 2026
| N 14:28 | AMK-Library diffhist +131 Oluschinski talk contribs (Created page with "You can find a current list of all works of the AMK-Library here: *[http://amk-merseburg.de/buechersammlung/ www.amk-merseburg.de]") | ||||
| 12:43 | Ultrasound Testing diffhist −52 Oluschinski talk contribs | ||||
| 11:19 | Testing diffhist −39 Oluschinski talk contribs | ||||
| 10:47 | Sink Mark diffhist +81 Oluschinski talk contribs | ||||
| 10:40 | Seidler, Sabine diffhist −12 Oluschinski talk contribs | ||||
4 September 2026
| 14:15 | Polymer Testing diffhist −23 Oluschinski talk contribs | ||||
| N 14:02 | Plastic Component diffhist +10,747 Oluschinski talk contribs (Created page with "{{Language_sel|LANG=ger|ARTIKEL=Kunststoffbauteil}} {{PSM_Infobox}} <span style="font-size:1.2em;font-weight:bold;">Plastic component, Dimensioning</span> __FORCETOC__ ==General== For designers of plastic products, the task increasingly involves selecting materials, dimensioning and designing components using scientifically based, plastics-specific working methods. ==Strength and deformation verification== The current approach to dimensioning plastic com...") | ||||
| N 10:42 | Micropores diffhist +3,185 Oluschinski talk contribs (Created page with "{{Language_sel|LANG=ger|ARTIKEL=Mikroporen}} {{PSM_Infobox}} <span style="font-size:1.2em;font-weight:bold;">Micropores</span> During the injection moulding process, volume contraction (see: processing shrinkage) occurs as the material cools. In areas where material has accumulated, this volume contraction of the melt is greater, and the reduced volume cannot be replaced by fresh melt. As a result, Tensile Test Residual Stresses Orientations|...") | ||||
| 10:38 | Measuring Uncertainty diffhist −2 Oluschinski talk contribs | ||||
| 10:36 | Measured Value diffhist −18 Oluschinski talk contribs | ||||
| 10:34 | Materials Testing diffhist −112 Oluschinski talk contribs | ||||
| 10:34 | Material & Werkstoff diffhist −2 Oluschinski talk contribs | ||||
| 08:57 | Hole Formation Plastics diffhist −83 Oluschinski talk contribs | ||||
| 08:56 | Hole Formation Films diffhist −15 Oluschinski talk contribs | ||||
| 08:46 | Grellmann, Wolfgang diffhist −15 Oluschinski talk contribs | ||||
| 08:38 | Gas Bubbles diffhist −123 Oluschinski talk contribs | ||||
3 September 2026
| 14:27 | Fracture Behaviour of Plastics Components diffhist −59 Oluschinski talk contribs | ||||
| N 14:07 | Failure Analysis Plastics Products, VDI Guideline 3822 diffhist +19,265 Oluschinski talk contribs (Created page with "{{Language_sel|LANG=ger|ARTIKEL=Schadensanalyse VDI Richtlinie 3822}} {{PSM_Infobox}} <span style="font-size:1.2em;font-weight:bold;">Fatigue analysis plastics products, VDI Guideline 3822</span> __FORCETOC__ ==Introduction== Plastic products are designed and manufactured with economic considerations in mind to ensure functional, safe and hazard-free use throughout their intended service life. Despite careful design, planning and production, damage and defects in plast...") | ||||
| N 14:05 | Failure Analysis – Basics diffhist +12,403 Oluschinski talk contribs (Created page with "{{Language_sel|LANG=ger|ARTIKEL=Schadensanalyse}} {{PSM_Infobox}} <span style="font-size:1.2em;font-weight:bold;">Failure analysis – Basics</span> __FORCETOC__ ==Failure analysis, evaluation of damage cases== Damage analyses serve to determine the causes of component failure and to draw conclusions from this in order to initiate targeted measures for damage repair and prevention. A wide range of analytical methods, Polymer Testing|polymer tes...") | ||||
| 13:51 | Error Limit diffhist −3 Oluschinski talk contribs | ||||